IngramSpark prints and distributes books to bookstores, libraries and online retailers worldwide, including Amazon. It runs on the same printers as Ingram’s Lightning Source, and its file checks are stricter than KDP’s. A file that passes on KDP can still come back from IngramSpark, usually because of margins, fonts or color settings. Here’s what it checks, in plain language.
The requirements for the book’s pages
Pages and cover are separate PDFs
Upload the book’s pages as one PDF and the cover as another. IngramSpark calls the pages file the “interior file”.
One page per sheet, at your trim size
Use single pages (IngramSpark says “1-up”), not two-page spreads. Every page must be exactly your trim size, or trim size plus bleed if you use it.
No printer marks
Remove crop marks, registration marks and printer’s marks when you export. IngramSpark trims the book itself.
All fonts embedded
Every font used, including in headers and page numbers, must be embedded in the PDF. In a PDF reader, check under File → Properties → Fonts.
Keep text 0.5 in from the edges
IngramSpark recommends a minimum margin of 0.5 in (13 mm) from the trim on all sides, and says this includes page numbers and running heads. Printing can vary by 1/16 in, so anything closer risks being cut off.
Bleed is 0.125 in, except at the spine
If anything prints to the edge of the page, extend it 0.125 in (3 mm) past the trim on the top, bottom and outside edges, but not on the spine side. A text-only book doesn’t need bleed.
Black-and-white books use grayscale images
For a black-and-white book, convert every image to grayscale and remove spot colors and ICC color profiles.
Color books use CMYK at 300 ppi
For a color book, IngramSpark recommends 300 ppi images, total ink (CMYK) no higher than 240%, no “registration black”, and spot colors converted to CMYK before export.
The last page is blank
The final page of the file should be blank. If it isn’t, IngramSpark adds one, which can change your page count by one.
Export as PDF/X-1a
IngramSpark recommends the PDF/X-1a:2001 standard. Professional layout programs offer it as an export preset. A standard PDF with embedded fonts is often accepted, but PDF/X-1a avoids most rejections.
Revisions mean a full new file
To fix a typo after upload, re-upload the whole PDF. IngramSpark doesn’t accept replacement pages.
How IngramSpark differs from KDP
| Check | KDP | IngramSpark |
|---|---|---|
| Outside margins | At least 0.25 in (no bleed) | 0.5 in recommended on all sides |
| Inside margin | Grows with page count, from 0.375 in | 0.5 in recommended (wider is wise for thick books) |
| Bleed | 0.125 in, page grows on three sides | 0.125 in, not on the spine side |
| PDF standard | Any print PDF with embedded fonts | PDF/X-1a:2001 recommended |
| Last page | No rule | Blank (added if missing) |
| ISBN | Free KDP ISBN available, KDP use only | Your own ISBN |
The practical rule: build to IngramSpark’s margins and the same PDF will pass on both. KDP’s minimums are smaller, so a file with 0.5 in or more on every side, and a wider gutter for longer books, satisfies both printers. See KDP trim sizes and margins for KDP’s gutter table.
Trim sizes and page counts
IngramSpark offers the standard trade sizes, including 5 × 8, 5.5 × 8.5 and 6 × 9 in, in paperback and hardcover, on cream or white paper. Available sizes, bindings and minimum page counts depend on the combination you choose, so check its “Available Trim Sizes, Bindings for Covers & Interior Papers” page before you lay out the book. Choose the trim size first, because your PDF must match it exactly.
The cover
The cover is a single PDF with back, spine and front, sized from your trim, paper and final page count. IngramSpark has a free cover template generator that builds the template and barcode for your ISBN. Make the cover only once the pages are final, because any change in page count changes the spine width. Our spine width calculator gives a quick estimate, but use IngramSpark’s own template for the upload.
The ebook
For the ebook edition, IngramSpark takes an EPUB. Validate it with EPUBCheck first; a file with errors is rejected. The ebook needs its own ISBN, different from the print edition’s. See which file each store needs.
Before you upload: a quick self-check
- Open the PDF and confirm the page size under File → Properties.
- Check the font list: every font should say “Embedded” or “Embedded Subset”.
- Flip through: page numbers and running heads should sit comfortably inside the edges.
- Check the page count is even and the last page is blank.
- Make sure the title and author on the title page match your IngramSpark title setup exactly.
The print-ready PDF from Manuscript Packet is built to these numbers: single pages at your trim size, fonts embedded, running heads and page numbers kept at least 0.5 in from the edges, an even page count, and a gutter that widens for longer books. The print-ready checklist covers the remaining checks.
Requirements are from IngramSpark’s help article “Interior File Creation”. IngramSpark updates its specifications from time to time; its File Creation Guide has the full detail.